Electric electromagnetic marking pin marking the first marking machine needles
ID: 59215

Electric electromagnetic marking pin marking the first marking machine needles

0.0 (1 votes) | 5 orders
Price:
US $ 133.20 / piece
Quantity

Buy Now
Add to Cart


Electromagnetic marking pin can replace the traditional pneumatic marking pin marking machine on than pneumatic marking machine saves the solenoid valve and pump parts, save the trouble of connecting gas line and pump noise annoyance, you can play the original pneumatic changes directly on the standard machine, convenient, supports a variety of marking machine control panel, are welcome.

First, the product parameters

1. Controller Dimensions: Length: 90mm Width: 37mm height: 21mm

2. Controller installation pitch dimensions: 73mm Φ3 * 2

3. Marking needle assembly: Length 71mm maximum diameter: Φ36mm

4. Needle core diameter: 2.5mm 3.5mm

5. Marking assembly dimensions: The following chart

6. intensity adjustment: GN-BL6F for 10, GN-BL4F for four

7. efforts frequency: Yes

8. Replace the needle core: Yes

9. The minimum distance between the needle: 0.5mm

10. The maximum distance between the needle: 4mm

11. Applicable Material: hard plastic, aluminum, iron, stainless steel, etc.

12. needle core hardness: HRA94

13. Marking the highest hardness: HRC68

14. printable lines or dots

Second, the electrical parameters

1. Input voltage: DC24V ± 5%

2. Power: 6-20W (depending on the intensity of the marking may be)

3. Input signal: 24V ± 10% active high

4. The maximum operating temperature marking assembly: 45

5. misuse protection with control buttons

6. Internal accuracy with automatic control circuit

7. The energy-saving design, low power processing non-working state, the power consumption of less than 0.3W

8. The controller waterproof, dustproof, anti-oil, shockproof

Third, the electrical connection

1. Red: + 24V input (directly connected to the switching power supply + 24V)

2. The black line: GND (GND directly to the switching power supply or 0V)

3. White line: intensity adjustment (to be connected to self-reset switch)

4. Blue Line: signal input (with solenoid valve control board terminal positive)

5. yellow line: electromagnetic marking assembly (no polarity distinction)

for 3: The two white wires are directly connected together and after three seconds it is the intensity adjustment mode

To adjust the intensity is to short the two white lines for three seconds
Long pressing the switch for three seconds is the same as touching the two white wires for three seconds
After shorting together for three seconds, the needle will keep vibrating. Now it is in the strength adjustment mode. Then disconnect the two white wires, and then short the needle to change the strength level.


Fourth, efforts to regulate

1. In the controller's two white lines connected to self-reset switch (eg: print switch)

2. The controller is plugged in and connected to the assembly marking

3. The machine is in the idle state

4. Press the switch more than 2 seconds to enter the intensity of selection mode, marking the moment the needle is in a state of shock, vibration amplitude size represents the intensity of the current marking, again pressed into the intensity adjustment mode, each button can be replaced marking efforts, if 3 no operation within 5 seconds and will exit the intensity adjustment mode and memory current intensity (no need to select the intensity of the next boot).

5. You can not adjust the intensity of the marking process, complete the time of this printing or stopped before proceeding.

V. Notes

1. Do not pick the wrong power supply controller, connected to the wrong controller will burn. (Void the warranty)

2, the back-end assembly screws, a wire section can not exceed 3.5mm, or affect the needle work (see below)

3, marking the outgoing assembly, the need to strengthen protection, should prevent disconnection

4, assembly marking process Caton phenomenon, please remove the needle spring cleaning or replacement

5, please carefully check your wiring is correct after installation, confirmation and then power test machine

6. Select the appropriate marking efforts will improve the life of the needle core.

7. Do not disassemble the controller and the marking head assembly, disassembly will be deemed a waiver of the warranty.

8, when the machine is working, please do not touch the marking assembly, to prevent accidents.

9, the first installation of the need for stylus tightened to prevent loosening of the marking process, the factory did not tighten.

10. The self-locking access control (debug) switch, control signal line, not connected to the power supply switch (red + 24V) on the controller, it will increase the wake-up time of the controller.

Unit: mm


  • Application: Grinder
  • Model Number: Electric electromagnetic marking pin
  • Origin: Mainland China
  • Certification: CE

SHIPPING AND DELIVERY

We are proud to offer international shipping services that currently operate in over 200 countries and islands world wide. Nothing means more to us than bringing our customers great value and service. We will continue to grow to meet the needs of all our customers, delivering a service beyond all expectation anywhere in the world.

How do you ship packages?

Packages from our warehouse in China will be shipped by ePacket or EMS depending on the weight and size of the product. Packages shipped from our US warehouse are shipped through USPS.

Do you ship worldwide?

Yes. We provide free shipping to over 200 countries around the world. However, there are some location we are unable to ship to. If you happen to be located in one of those countries we will contact you.

What about customs?

We are not responsible for any custom fees once the items have shipped. By purchasing our products, you consent that one or more packages may be shipped to you and may get custom fees when they arrive to your country.

How long does shipping take?

Shipping time varies by location. These are our estimates:

Location *Estimated Shipping Time
United States 10-30 Business days
Canada, Europe 10-30 Business days
Australia, New Zealand 10-30 Business days
Central & South America 15-30 Business days
*This doesn’t include our 2-5 day processing time.

Do you provide tracking information?

Yes, you will receive an email once your order ships that contains your tracking information.

My tracking says “no information available at the moment”.

For some shipping companies, it takes 2-5 business days for the tracking information to update on the system.

Will my items be sent in one package?

For logistical reasons, items in the same purchase will sometimes be sent in separate packages, even if you've specified combined shipping.

If you have any other questions, please contact us and we will do our best to help you out.

REFUNDS & RETURNS POLICY

Order cancellation

All orders can be cancelled until they are shipped. If your order has been paid and you need to make a change or cancel an order, you must contact us within 12 hours. Once the packaging and shipping process has started, it can no longer be cancelled.

Refunds

Your satisfaction is our #1 priority. Therefore, if you’d like a refund you can request one no matter the reason.

If you did not receive the product within the guaranteed time(45 days not including 2-5 day processing) you can request a refund or a reshipment.

If you received the wrong item you can request a refund or a reshipment.

If you do not want the product you’ve receive you may request a refund but you must return the item at your expense and the item must be unused.

  • Your order did not arrive due to factors within your control (i.e. providing the wrong shipping address)
  • Your order did not arrive due to exceptional circumstances outside the control of HOGAKI.COM - Home, Garden & Kitchen shop (i.e. not cleared by customs, delayed by a natural disaster).
  • Other exceptional circumstances outside the control of hogaki.com

*You can submit refund requests within 15 days after the guaranteed period for delivery (45 days) has expired. You can do it by sending a message on Contact Us page

If you are approved for a refund, then your refund will be processed, and a credit will automatically be applied to your credit card or original method of payment, within 14 days.

Exchanges

If for any reason you would like to exchange your product, perhaps for a different size in clothing. You must contact us first and we will guide you through the steps.

Please do not send your purchase back to us unless we authorise you to do so.

LARGE ORDER DEALS

Wholesale

Thank you for your interest doing business with us!

If you would like to get a discounted price for your large purchase orders, fill in the required blanks along with your email address, the product Item ID # and/or the link of the item that you want to order, item quantity (minimum of 30 pieces), shipping country and payment method is required. We will contact you with a discounted price as soon as we receive your inquiry.

You may also like these products